DrayTek UK Users' Community Forum

Help, Advice and Solutions from DrayTek Users

EE HUAWEI E392 USB 4g tested and working on 2830 and 2850

More
11 Jun 2013 08:33 #76489 by morethanit
Apologies - I omitted the firmware level from previous post.
It is 3.6.4 and I have tried to use both a 2830 & 2850.
Signal strength is 50%.
I am using the APN everywhere and correct login details.
Issue - is that it is logging in and connecting, but no IP address is being allocated.
The dongle works fine if direct connected to a PC, but does seem to take a long time to initialise.

I seem to be my own particular world of pain as these settings seem to work for everyone else.
Suggestions gratefully appreciated.

Please Log in or Create an account to join the conversation.

  • eric.jansen
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
12 Jun 2013 22:01 #76542 by eric.jansen

morethanit wrote: Hi,

Here is my (truncated syslog)
21:44:24 WAN 3 is up.
21:44:24 WAN3 PPPoE <== Protocol:IPCP(8021) ConfAck Identifier:0x01 IP Address: 10 5 247 xxx Primary Domain Name Server......
21:44:24 WAN3 PPPoE ==> Protocol:IPCP(8021) ConfReq Identifier:0x01 IP Address: 10 5 247 xxx Primary Domain Name Server.......
21:44:24 WAN3 PPPoE <== Protocol:IPCP(8021) ConfNak Identifier:0x00 IP Address: 10 5 247 xxx Primary Domain Name Server.......
21:44:24 WAN3 PPPoE ==> Protocol:IPCP(8021) ConfAck Identifier:0x01 ##
21:44:24 WAN3 PPPoE <== Protocol:IPCP(8021) ConfReq Identifier:0x01 ##
21:44:24 WAN3 PPPoE ==> Protocol:IPCP(8021) ConfReq Identifier:0x00 IP Address: 0 0 0 0 Primary Domain Name Server: 0 0 0 0 Secondary Domain Name Server: 0 0 0 0 ##
21:44:24 WAN3 PPPoE <== Protocol:CHAP(c223) Success Identifier:0x01 ##
21:44:24 WAN3 PPPoE ==> Protocol:CHAP(c223) Response Identifier:0x01 ......
21:44:24 WAN3 PPPoE <== Protocol:CHAP(c223) Challenge Identifier:0x01 ......
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) DiscReq Identifier:0x09Magic Number: 0x2e7 d3 d6 ##
21:44:24 WAN3 PPPoE ==> Protocol:LCP(c021) ConfAck Identifier:0x08 ACCM: 0x0 Authentication Type: CHAP 05 ...
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) ConfReq Identifier:0x08 ACCM: 0x0 Authentication Type: CHAP 05 ...
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) ConfAck Identifier:0x01 MRU: 1500 ACCM: 0x0 Address/Control Field Compression ##
21:44:24 WAN3 PPPoE ==> Protocol:LCP(c021) ConfRej Identifier:0x07 Protocol Field Compression ##
21:44:24 WAN3 PPPoE <== Protocol:LCP(c021) ConfReq Identifier:0x07 ACCM: 0x0 Authentication Type: CHAP 05 ...
21:44:23 WAN3 PPPoE ==> Protocol:LCP(c021) ConfReq Identifier:0x01 MRU: 1500 ACCM: 0x0 Address/Control Field Compression ##
21:44:21 [3G]Modem status:A1 20 00 00 00 00 02 00 03 00 len=10
21:44:21 [3G]Modem response: CONNECT 100000000
21:44:21 [3G]Modem dial [ATDT*99# ]
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Modem prepare to dial [AT ]
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Modem initialize2 [AT ]
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Modem initialize [AT+CGDCONT=1,'IP','everywhere' ]
21:44:21 [3G]Good. Don't need PIN code
21:44:21 [3G]Modem response: +CPIN: READY OK
21:44:21 [3G]Send command AT+CPIN?
21:44:21 [3G]Modem response: +CSQ: 26,99 OK
21:44:21 [3G]Query for signal strength AT+CSQ
21:44:21 [3G]Modem response: OK
21:44:21 [3G]Send default init command AT&FE0V1X1&D2&C1S0=0 #1
21:44:21 WAN3 PPPoE <== Protocol:LCP(c021) ProtRej Identifier:0x06Rejected Protocol: 0x7eff .....
21:44:21 WAN3 PPPoE ==> Protocol:LCP(c021) ConfReq Identifier:0x00 MRU: 1500 ACCM: 0x0 Address/Control Field Compression ##
21:44:21 WAN3 PPPoE <== V:1 T:1 PADS ID:0

Please Log in or Create an account to join the conversation.

  • eric.jansen
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
25 Jun 2013 09:03 #76798 by eric.jansen

morethanit wrote: Apologies - I omitted the firmware level from previous post.
It is 3.6.4 and I have tried to use both a 2830 & 2850.
Signal strength is 50%.
I am using the APN everywhere and correct login details.
Issue - is that it is logging in and connecting, but no IP address is being allocated.
The dongle works fine if direct connected to a PC, but does seem to take a long time to initialise.

I seem to be my own particular world of pain as these settings seem to work for everyone else.
Suggestions gratefully appreciated.



Hi,
As I have cancelled my 4GEE contract and have no longer any use for the Huwei 4G dongle, I am happy to sell it on. Who knows the issues are with possible different Firmware.
Just reply via PM if you are interested.

Please Log in or Create an account to join the conversation.

Moderators: ChrisSami