DrayTek UK Users' Community Forum

Help, Advice and Solutions from DrayTek Users

O2 Broadband Setup 2830

  • mark_s
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
07 Dec 2011 15:10 #70382 by mark_s
O2 Broadband Setup 2830 was created by mark_s
Hi guys,
Is there a link to the configuration / Setup for O2 Broadband in the UK

Is this a Draytek help or a O2 Support help.

Any Help would be appreciated.

ADSL2 using Router.
I will log into SUPERUSER later to see if i can gleem any settings.

Is there a setup guide already out there.


Thanks

Please Log in or Create an account to join the conversation.

More
07 Dec 2011 15:26 #70384 by nealuk
Replied by nealuk on topic Re: O2 Broadband Setup 2830
This is the Draytek users forum. There are some O2 tips here: http://www.draytek.co.uk/support/kb_vigor100_setup.html

Regards, Neal

Please Log in or Create an account to join the conversation.

  • mark_s
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
07 Dec 2011 16:55 #70385 by mark_s
Replied by mark_s on topic Re: O2 Broadband Setup 2830
Thank You

New to the Draytek forums and sometimes it easier just to ask.

Thanks for the link appreciated.

Please Log in or Create an account to join the conversation.

  • mark_s
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
08 Dec 2011 08:07 #70403 by mark_s
Replied by mark_s on topic Re: O2 Broadband Setup 2830
Problems Problems until i installed the latest firware update.

Firmware Version : 3.3.6.1sb
Release Date : 1st July 2011

At First the connection would keep dropping but after installing the latest firmware update it seemed to work. (Not Fully Tested only worked for 20mins as i ran out of time).
Now after receiving the Router as my first post was pre arrival i was also guided to the setup wizard by o2, before i done the update this failed and then we used the following settings.


Draytek Router Settings
To access the internet settings configuration section, click WAN > internet access.

Click the PPPoE / PPPoA tab

Select disable and click ok.


To enter the settings for the O2 connection click the (MPoA) tab.

Draytek Router Settings:

The first option is enable or disable for this tab, select enable

Multi PVC channel: Channel 2

Encapsulation: 1483 Bridged IP LLC

VPI: 0

VCI: 101

Modulation: ADSL2+ / ADSL2+ annex M

RIP protocol: disabled

Bridge mode: disabled

WAN IP network settings: auto / static IP address, this is dependent on whether the customer has a static IP or not

Router name: Blank

Domain name: Blank

Mac address: Default MAC address.

DNS server IP: Enter manually if using a static IP.
- - - - - -- - - - -

o2 Broadband Settings for Draytek 2830n

The only way prior to the firware update to connect was to to do a factory reset.
Put the settings in again and wait for about 5 mins.
The online status would change from

READ
HANDSHAKING
INTALSTART (Something like that)
FAIL

Now after installing the Firmware Update it connects straight away.

My Previous Firmare was 3.3.6 (April) if i remember there was very little time between the updates and i can see why now lol

Hope my experience helps others too.

Mark

Please Log in or Create an account to join the conversation.

More
08 Dec 2011 10:57 #70406 by voodle
Replied by voodle on topic Re: O2 Broadband Setup 2830
Set the modulation to ADSL2+ (G.992.5) or multimode, if it doesn't sync with Annex M then maybe your line doesn't have Annex M enabled on it.

Please Log in or Create an account to join the conversation.

Moderators: ChrisSami