DrayTek UK Users' Community Forum

Help, Advice and Solutions from DrayTek Users

2820 3.3.5.2 port forwards stop working

  • robathome
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
10 Oct 2011 15:21 #69638 by robathome
2820 3.3.5.2 port forwards stop working was created by robathome
Has anyone else had the issue with their port forwards not working? I have setup a couple of port forwards for RDPing into the PCs here. All working fine for ages, but since upgrading to 3.3.5.2 they are patchy - reboot the router and they work, then a few hours later they stop working - all of them.

Please Log in or Create an account to join the conversation.

More
12 Oct 2011 11:31 #69659 by howard simpson
Replied by howard simpson on topic Re: 2820 3.3.5.2 port forwards stop working
I have this problem I have several port redirects that used to work. However now my NAS box port redirect does not work yet the one to my AP700 management page does!

Howard

Please Log in or Create an account to join the conversation.

More
12 Oct 2011 11:53 #69660 by philtrick
Replied by philtrick on topic Re: 2820 3.3.5.2 port forwards stop working
I've posted seperately about UPNP port redirect 8080 not working, previously all ok.
I checked the UPNP port redirection table via telnet all looks ok (see below). The other UPNP ports redirections work ok i.e. 20, 21, 80, 443.
If I manually enter the port 8080 redirection in the NAT table all is ok. Any ideas- poor firmware??

Is this forum monitored by draytek technical support?

> upnp nat
****************** IGD NAT Status ****************

((0))
InternalClient >>192.168.1.10<<, RemoteHost >>0.0.0.0<<
InternalPort >>21<<, ExternalPort >>21<<
PortMapProtocol >>TCP<<
The tmpvirtual server index >>0<<
PortMapLeaseDuration >>0<<, PortMapEnabled >>1<<
FTP/FTPS
((1))
InternalClient >>192.168.1.10<<, RemoteHost >>0.0.0.0<<
InternalPort >>8080<<, ExternalPort >>8080<<
PortMapProtocol >>TCP<<
The tmpvirtual server index >>0<<
PortMapLeaseDuration >>0<<, PortMapEnabled >>1<<
Web Admin
((2))
InternalClient >>192.168.1.10<<, RemoteHost >>0.0.0.0<<
InternalPort >>20<<, ExternalPort >>20<<
PortMapProtocol >>TCP<<
The tmpvirtual server index >>1<<
PortMapLeaseDuration >>0<<, PortMapEnabled >>1<<
FTP/FTPS
((3))
InternalClient >>192.168.1.10<<, RemoteHost >>0.0.0.0<<
InternalPort >>80<<, ExternalPort >>80<<
PortMapProtocol >>TCP<<
The tmpvirtual server index >>2<<
PortMapLeaseDuration >>0<<, PortMapEnabled >>1<<
Web Server/Multimedia Station
((4))

Please Log in or Create an account to join the conversation.

  • robathome
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
12 Oct 2011 12:17 #69661 by robathome
Replied by robathome on topic Re: 2820 3.3.5.2 port forwards stop working
I had a version of 3.3.5.2 on that was supposed to cope better with dodgy adsl (211801 alternative)

I have since "upgraded" again to the latest and haven't had the port forward issue since. Either of you two on the firmware above?

ta

Please Log in or Create an account to join the conversation.

More
12 Oct 2011 12:30 #69663 by philtrick
Replied by philtrick on topic Re: 2820 3.3.5.2 port forwards stop working
I'm using Firmware Version: 3.3.5.2_232201 which I understand is the latest firmware from the UK support site. Is there a later version available from a different site?
I'm not using the ADSL function on the router because I have BT Infinity which terminates on the WAN Ethernet port.

Sounds like 3.3.5.2 is dodgy where is the working software located?

Please Log in or Create an account to join the conversation.

  • robathome
  • Topic Author
  • Offline
  • Junior Member
  • Junior Member
More
12 Oct 2011 14:40 #69665 by robathome
Replied by robathome on topic Re: 2820 3.3.5.2 port forwards stop working
I am only using the latest one on the UK site like yours.
I use ADSL and ethernet (FTTC) here...

Please Log in or Create an account to join the conversation.

Moderators: ChrisSami