DrayTek UK Users' Community Forum

Help, Advice and Solutions from DrayTek Users

2710n QoS stupidity...

  • danfloun
  • Topic Author
  • Offline
  • New Member
  • New Member
More
29 Nov 2009 13:55 #59085 by danfloun
2710n QoS stupidity... was created by danfloun
Well I ordered a 2710Vn, received a 2710n but aren't particularly bothered except for the fact that the QoS led on the box is 'on' and my upload speed has dropped from around 34*Kb with my DG834GT router to around 25*Kb with the 2710n.

As the 2710, 2710n & 2710Vn all use the same firmware, I'm assuming QoS is reserving bandwidth for VOIP even though I don't have that model.
I think Draytek have been rather lazy about this, they could have easily had 2 firmwares with QoS disabled on the 2710 & 2710n.

To unsult me even more, after paying twice as much for this router than I did with the trusty DG834GT, I can't even disable QoS....

What logic is this?

Are Draytek mental or am I missing something here?

Danny

Please Log in or Create an account to join the conversation.

More
29 Nov 2009 23:14 #59094 by voodle
Replied by voodle on topic 2710n QoS stupidity...
It might be that despite QoS not really being used on the router, the bandwidth reservation for it is still in place, to change that, access the router's telnet interface and enter these commands:

adsl txpct 100
adsl rxpct 100
adsl reboot

which will put the tx and rx rate up to 100% for the adsl connection.

Please Log in or Create an account to join the conversation.

  • danfloun
  • Topic Author
  • Offline
  • New Member
  • New Member
More
29 Nov 2009 23:29 #59095 by danfloun
Replied by danfloun on topic 2710n QoS stupidity...

Voodle wrote: It might be that despite QoS not really being used on the router, the bandwidth reservation for it is still in place, to change that, access the router's telnet interface and enter these commands:

adsl txpct 100
adsl rxpct 100
adsl reboot

which will put the tx and rx rate up to 100% for the adsl connection.



Just tried that and BINGO, it fixed it.

Thanks a lot

Please Log in or Create an account to join the conversation.

  • danfloun
  • Topic Author
  • Offline
  • New Member
  • New Member
More
30 Nov 2009 01:20 #59097 by danfloun
Replied by danfloun on topic 2710n QoS stupidity...
For anyone interested, it appears that QoS is implemented on the 2710n and more than likely also on the 2710Vn & 2710, it's just that Draytek have removed the gui on the uk models!

If you're willing to work through it and experiment, you can configure it via telnet commands. For those who simply want to turn it off completely (it comes enabled by default) then telnet into your box and simply type each line below followed by enter.

Code:
qos setup -m 1 sys commit sys reboot


Your box will reboot without QoS.

Danny

Please Log in or Create an account to join the conversation.

More
14 Dec 2009 06:54 #59343 by bombhead69
Replied by bombhead69 on topic 2710n QoS stupidity...
ultra dumb here :( ...but where do I put these commands in?...what is telnet?

Please Log in or Create an account to join the conversation.

  • danfloun
  • Topic Author
  • Offline
  • New Member
  • New Member
More
14 Dec 2009 11:37 #59345 by danfloun
Replied by danfloun on topic 2710n QoS stupidity...

bombhead69 wrote: ultra dumb here :( ...but where do I put these commands in?...what is telnet?



You have to telnet into the router.
Assuming you are on windows;

Start menu -> run -> type cmd and press enter.
Then in the black window type telnet (address of router, e.g. telnet 192.168.1.1) and press enter.

You will then be asked for your password for the router, type it in and press enter. You now enter the commands above it you want to disable QoS.

Please Log in or Create an account to join the conversation.

Moderators: ChrisSami